Equipment specification according to GOST. System of design documents for construction. Rules for fulfilling the specifications of equipment, products and materials Filling out the specifications according to GOST 21.110

GOST 21.110-95

INTERSTATE STANDARD

DESIGN DOCUMENTATION SYSTEM
FOR CONSTRUCTION

RULES FOR IMPLEMENTING THE SPECIFICATION
EQUIPMENT, PRODUCTS
AND MATERIALS

INTERSTATE SCIENTIFIC AND TECHNICAL COMMISSION FOR STANDARDIZATION AND TECHNICAL REGULATION IN CONSTRUCTION

Moscow

Preface

1 DEVELOPED by the State Enterprise - Center for Methodology, Standardization and Standardization in Construction (GP TsNS), State Design and Construction Institute Project-Montazhavtomatika and State Design, Construction and Research Institute SantekhNIIproekt

INTRODUCED by the Ministry of Construction of Russia

2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization and Technical Regulation in Construction on April 19, 1995

3 ENTERED INTO EFFECT on June 1, 1995 as a state standard of the Russian Federation by Decree of the Ministry of Construction of Russia dated 06/05/95 No. 18-55

4 INSTEAD GOST 21.109-80, GOST 21.110-82 and GOST 21.111-84

MEZhSTATESTANDARD

System of design documents for construction

RULES FOR COMPLETING SPECIFICATIONS OF EQUIPMENT, PRODUCTS AND MATERIALS

System of building design documents
Rules of developing specifications for equipment, products and materials

Date of introduction 1995-06-01

1 AREA OF USE

Real th standard establishes requirements for the implementation of specifications of equipment, products and materials for the main sets of working drawings of buildings and structures for various purposes.

2 REGULATORY REFERENCES

This standard uses reference to GOST 21.101 -93 SPDS. Basic requirements for working documentation.

3 DEFINITIONS

In this standard the following term is used Specification of equipment, products and materials- a textual design document defining the composition of equipment, products and materials intended for acquisition, preparation and implementation of construction.

4 EXECUTION OF EQUIPMENT SPECIFICATIONS,
PRODUCTS AND MATERIALS

4.1 The specification of equipment, products and materials (hereinafter referred to as the Specification) is compiled according to e 1 to all main sets of working drawings (except for the main sets of working drawings of building structures).

4.2 The specification includes all equipment, products and materials provided for in the working drawings of the corresponding main set.

4.3 The specification, as a rule, is compiled into sections (subsections), the composition of which, and the sequence of recording equipment, products and materials in them, are established by the relevant SPDS standards.

The name of each section (subsection) is written as a heading in column 2 and underlined.

4.4 The Specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.

4.5 The Specifications indicate:

In column 1 - positional designations of equipment, products provided for in the working drawings of the corresponding main set;

In column 2 - the name of the equipment, product, material, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document;

In column 3 - the type, brand of equipment, product, designation of the standard, technical specifications or other document, as well as the designation of the questionnaire;

In column 4 - code of equipment, product, material according to the product classifier;

About column 5 - name of the equipment manufacturer (for imported equipment - country, company);

Column 6 - designation of the unit of measurement;

In column 7 - the quantity of equipment, products, materials;

In column 8 - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment (weighing up to 25 kg) that does not require the use of lifting vehicles during installation, the column may not be filled in;

Column 9 contains additional information.

4.6 In the Specification, when recording equipment and individually manufactured products, columns 4 and 5 are not filled in, and in column 8 the approximate weight of a piece of equipment is indicated.

4.7 The specification of equipment, products and materials is drawn up as an independent document, which is assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and, separated by a dot, code C.

Example - 2345 - 11 - TX.S, 2345 - 11 - OV.S, 2345 - 11 - ATX.S.

4.8 The first sheet of the Specification is the title page, made according to.

It is allowed to omit the title page. In this case, on the first sheet of the Specification, instead of the main inscription according to Form 5, the main inscription according to Form 3 GOST 21.101 is made.

4.9 The specification of equipment, products and materials is included in the list of reference and attached documents (Form 2 GOST 21.101), in the section “Attached Documents” and is issued to the customer in the quantity established for working drawings.

* The name of the ministry (department) may not be indicated.

Key words: Specification of equipment, products and materials, execution

GOST 21.110-95

UDC 691:002.006.354

Group Zh01

INTERSTATE STANDARD

System of design documents for construction

RULES FOR FOLLOWING EQUIPMENT SPECIFICATIONS,

PRODUCTS AND MATERIALS

System of building design documents

Rules of developing specifications for equipment, products and materials

Date of introduction 1995-06-01

Preface

1 DEVELOPED by the State Enterprise - Center for Methodology, Standardization and Standardization in Construction (GP TsNS), State Design and Construction Institute Proektmontazhavtomatika and State Design, Construction and Research Institute SantekhNIIproekt

INTRODUCED by the Ministry of Construction of Russia

2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization and Technical Regulation in Construction on April 19, 1995

3 ENTERED INTO EFFECT by Resolution of the Ministry of Construction of Russia dated 06/05/95 No. 18-55 as a state standard of the Russian Federation from July 1, 1995.

4 INSTEAD GOST 21.109-80, GOST 21.110-82 and GOST 21.111-84

5 reissue. October 2001

1 APPLICATION AREA

This standard establishes requirements for the implementation of specifications of equipment, products and materials for the main sets of working drawings of buildings and structures for various purposes.

3 DEFINITIONS

In this standard the following term is used

Specification of equipment, products and materials- a textual design document defining the composition of equipment, products and materials intended for acquisition, preparation and implementation of construction.

4 EXECUTION OF EQUIPMENT SPECIFICATIONS,

PRODUCTS AND MATERIALS

4.1 The specification of equipment, products and materials (hereinafter referred to as the Specification) is drawn up in Form 1 for all main sets of working drawings (except for the main sets of working drawings of building structures).

4.2 The specification includes all equipment, products and materials provided for in the working drawings of the corresponding main set.

4.3 The specification, as a rule, is compiled into sections (subsections), the composition of which and the sequence of recording equipment, products and materials in them are established by the relevant standards of the Construction Design Documentation System (SPDS).

The name of each section (subsection) is written as a heading in column 2 and underlined.

4.4 The Specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.

4.5 The Specifications indicate:

In column 1 - positional designations of equipment, products provided for in the working drawings of the corresponding main set;

In column 2 - the name of the equipment, product, material, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document;

In column 3 - the type, brand of equipment, product, designation of the standard, technical specifications or other document, as well as the designation of the questionnaire;

In column 4 - code of equipment, product, material according to the product classifier;

In column 5 - name of the equipment manufacturer (for imported equipment - country, company);

Column 6 - designation of the unit of measurement;

In column 7 - the quantity of equipment, products, materials;

In column 8 - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment (weighing up to 25 kg) that does not require the use of lifting vehicles during installation, the column may not be filled in;

Column 9 contains additional information.

4.6 In the Specification, when recording equipment and individually manufactured products, columns 4 and 5 are not filled in, and in column 8 the approximate weight of a piece of equipment is indicated.

4.7 The specification of equipment, products and materials is drawn up as an independent document, which is assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and, separated by a dot, code C.

Example - 2345 - 11 - TX.S, 2345 - 11 - OV.S, 2345 - 11 - ATX.S.

4.8 The first sheet of the Specification is the title page, made according to Form 2.

It is allowed to omit the title page. In this case, on the first sheet of the Specification, instead of the main inscription according to Form 5, the main inscription according to Form 3 of GOST 21.101 is made.

4.9 The specification of equipment, products and materials is included in the list of reference and attached documents (Form 2 GOST 21.101), in the section “Attached Documents” and is issued to the customer in the quantity established for working drawings.

* The name of the ministry (department) may not be indicated.

Key words: Specification of equipment, products and materials, execution

page 1

page 2

page 3

page 4

page 5

page 6

page 7

page 8

page 9

Preface

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions" and GOST 1.2-2009 "Interstate standards. Rules and recommendations for interstate standardization. Rules for development, adoption, application, updating and cancellation.”

Standard information

1 DEVELOPED by the Open Joint-Stock Company “Center for Methodology of Standardization and Standardization in Construction” (JSC “CNS”)

2 INTRODUCED by the Technical Committee TC 465 “Construction”

3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (IGS) (protocol dated November 14, 2013 No. 44-2013)

4 By Order of the Federal Agency for Technical Regulation and Metrology dated December 17, 2013 No. 2310-st, the interstate standard GOST 21.110-2013 was put into effect as the national standard of the Russian Federation on January 1, 2015.

Information about changes to this standard is published in the annual information index “National Standards”, and the text of changes and amendments is published in the monthly information index “National Standards”. In case of revision (replacement) or cancellation of this standard, the corresponding notice will be published in the monthly information index “National Standards”. Relevant information, notifications and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet.

INTERSTATE STANDARD

System of design documents for construction

SPECIFICATIONS OF EQUIPMENT, PRODUCTS AND MATERIALS

System of design documents for construction.
Specification of equipment, products and materials.

Date of introduction - 2015-01-01

1 area of ​​use

This standard establishes the form and general rules for the implementation of specifications of equipment, products and materials as part of working documentation for the construction of facilities for various purposes.

2 Normative reference

Note - When using this standard, it is advisable to check the validity of the reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or using the annual information index “National Standards”, which was published as of January 1 of the current year, and on issues of the monthly information index “National Standards” for the current year. If the reference standard is replaced (changed), then when using this standard you should be guided by the replacing (changed) standard. If the reference standard is canceled without replacement, then the provision in which a reference is made to it is applied in the part that does not affect this reference.

3 Terms and definitions

In this standard, the following term is used with the corresponding definition:

3.1 specification of equipment, products and materials: A textual design document that defines the composition of equipment, products and materials and is intended for acquisition, preparation and implementation of construction.

4 General requirements

4.1 The specification of equipment, products and materials (hereinafter referred to as the specification) is drawn up in Form 1 for all main sets of working drawings, except for the main sets of working drawings of structural solutions (reinforced concrete, metal and wooden structures).

If the main set of working drawings of one brand is divided into several sets of the same brand, then a specification is drawn up for each of these sets.

It is allowed to modify the specification form, for example, to include additional columns in it, to change the size of the columns (except for the size of the columns of the main inscription and additional columns to it), in accordance with the requirements established in the standards of organizations.

It is allowed not to print horizontal lines delimiting specification lines, but it is necessary to maintain an interval of at least one printing digit between the texts of adjacent lines.

4.2 The specification is carried out on paper and/or in the form of an electronic document.

The specification in the form of an electronic document in the content part must have everything

data necessary for its output on information display media or on paper in accordance with the requirements of this standard.

4.3 The specification includes all equipment, materials and products provided for in the working drawings of the corresponding main set.

4.4 If an industrial building (structure) has attached or built-in parts in which auxiliary premises are located, then the specification is drawn up in parts, for example:

Production part;

Auxiliary part.

If a residential building has attached or built-in parts to accommodate enterprises and public institutions, then the specification is also drawn up in parts:

Residential part;

Auxiliary part.

4.5 The specification or its parts are usually compiled into sections and, if necessary, subsections. Within each section (subsection), equipment, products and materials are placed into groups, and within groups - in ascending order of their main parameters (for example: type, brand, diameter, cross-section, overall dimensions, etc.).

The specific composition of sections and subsections of the specification and the sequence of recording equipment, products and materials in them are established in the standards of the Construction Design Documentation System (SPDS) for types of construction and installation work.

The names of parts, sections and subsections are written in the column “Name and technical characteristics” in the form of a heading, symmetrical to the text, and underlined. In this case, the section and subsection headings should be separated from the text by an interval of one or two lines. The title may not be underlined.

4.6 The specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.

4.7 The specification indicates:

In the column "Pos." - positional designations * of equipment and products provided for in the working drawings of the corresponding main set;

* The designator may be numeric or alphanumeric.

In the column “Name and technical characteristics” - names of equipment, products, materials, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document. Before the name of equipment, products and materials, indicate their serial number of entry in the specification (usually within the section).

In a specification made in electronic form, the horizontal line included in the designation of materials (rolled products, pipes, etc.) can be replaced with a slash (/);

In the column “Type, brand, designation of a document, questionnaire” - the type, brand of equipment, product, designation of a standard, technical specifications or other document, as well as the designation of a questionnaire * if the ordering procedure requires the preparation of questionnaires;

* The forms of questionnaires are established by the manufacturer of the equipment or product.

In the column “Product code” - the code of the product (equipment, product, material) according to the product classifier of the country that developed the working documentation **. If standards, technical specifications, catalogs and other documents for products do not contain information on product codes, then this column is not filled in;

** Product codes according to product classifiers of other countries are not indicated.

In the “Supplier” column - the name (address) of the manufacturer or supplier of the equipment (for imported equipment - country, company);

In the column “Unit. measurement" - designation of the unit of measurement;

In the column "Count." - quantity of equipment, products, materials;

In the column “Weight of 1 unit, kg” - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment or products weighing up to 25 kg that do not require the use of lifting and transport vehicles during installation, the column may not be filled in;

In the “Note” column there is additional information.

4.8 In the specification, when recording equipment and individually manufactured products, the columns “Type, brand, designation of document, questionnaire” and “Product code” are not filled in, and in the column “Weight of 1 unit, kg” the approximate weight of a unit of equipment is indicated.

4.9 When using imported equipment, products and materials, they are recorded with the names and designations contained in the accompanying technical documentation (delivery documents).

It is allowed to simultaneously indicate authentic designations and names in Russian.

4.10 Specifications of equipment, products and materials are assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and through the code point “SO”.

Example - 2345-11-TX.SO, 2345-11-OV.SO, 2345-11-ATKH1.SO

4.11 The first sheet of the specification is the title page, made according to form 15 * GOST 21.101 on a sheet of A4 format. GOST 21.101.

4.12 On the title page the name of the specification is given indicating the name of the corresponding main set of working drawings.

Examples

1 Specification of equipment, products and materials for architectural solutions.

2 Specification of equipment, products and materials for external water supply and sewerage networks.

The name of the document in the title block on the title (first) sheet may be abbreviated as: “Specification of equipment, products and materials.”

4.13 The specification of equipment, products and materials is recorded in the “Attached Documents” section of the list of reference and attached documents, which is included in the general data on the working drawings of the corresponding main set.

Form 1 - Specification of equipment, products and materials

Key words: specification of equipment, products and materials, execution rules, working documentation, main set of working drawings, attached documents

GOST 21.110-95
Group Zh01

INTERSTATE STANDARD

System of design documents for construction
RULES FOR FOLLOWING EQUIPMENT SPECIFICATIONS,
PRODUCTS AND MATERIALS
System of building design documents.
Rules of developing specifications for equipment, products and materials

ISS 01.110
91.010.30
OKSTU 0021

Date of introduction 1995-06-01

Preface

1 DEVELOPED by the State Enterprise - Center for Methodology, Standardization and Standardization in Construction (GP TsNS), State Design and Construction Institute Proektmontazhavtomatika and State Design, Construction and Research Institute SantekhNIIproekt
INTRODUCED by the Ministry of Construction of Russia
2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization and Technical Regulation in Construction on April 19, 1995
The following voted for the adoption of the standard:

3 ENTERED INTO EFFECT by Resolution of the Ministry of Construction of Russia dated 06/05/95 N 18-55 as a state standard of the Russian Federation from June 1, 1995
4 INSTEAD GOST 21.109-80, GOST 21.110-82 and GOST 21.111-84
5 REPUBLICATION. July 2003

1 area of ​​use

1 area of ​​use

This standard establishes requirements for the implementation of specifications of equipment, products and materials for the main sets of working drawings of buildings and structures for various purposes.

2 Normative references

This standard uses reference to GOST 21.101-93* System of design documentation for construction. Basic requirements for design and working documentation.
_______________
* The document is not valid on the territory of the Russian Federation. GOST R 21.1101-2009 is valid, hereinafter in the text. - Database manufacturer's note.

3 Definitions

For the purposes of this standard, the following term is used.
Specification of equipment, products and materials- a textual design document defining the composition of equipment, products and materials intended for acquisition, preparation and implementation of construction.

4 Execution of specifications for equipment, products and materials

4.1 The specification of equipment, products and materials (hereinafter referred to as the Specification) is drawn up in Form 1 for all main sets of working drawings (except for the main sets of working drawings of building structures).

4.2 The Specification includes all equipment, products and materials provided for in the working drawings of the corresponding main set.

4.3 The specification, as a rule, is compiled into sections (subsections), the composition of which and the sequence of recording equipment, products and materials in them are established by the relevant standards of the Construction Design Documentation System (SPDS).
The name of each section (subsection) is written as a heading in column 2 and underlined.

4.4 The Specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.

4.5 The Specifications indicate:
- in column 1 - positional designations of equipment, products provided for in the working drawings of the corresponding main set;
- in column 2 - the name of the equipment, product, material, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document;
- in column 3 - type, brand of equipment, product, designation of the standard, technical specifications or other document, as well as designation of the questionnaire;
- in column 4 - code of equipment, product, material according to the product classifier;
- in column 5 - the name of the equipment manufacturer (for imported equipment - country, company);
- in column 6 - designation of the unit of measurement;
- in column 7 - the quantity of equipment, products, materials;
- in column 8 - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment (weighing up to 25 kg) that does not require the use of lifting vehicles during installation, the column may not be filled in;
- in column 9 - additional information.

4.6 In the Specification, when recording equipment and individually manufactured products, columns 4 and 5 are not filled in, and in column 8 the approximate weight of a piece of equipment is indicated.

4.7 The specification of equipment, products and materials is drawn up as an independent document, which is assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and, separated by a dot, code C.
Example - 2345-11-TX.S, 2345-11-OV.S, 2345-11-ATKH.S.

4.8 The first sheet of the Specification is the title page, made according to Form 2.
It is allowed to omit the title page. In this case, on the first sheet of the Specification, instead of the main inscription according to Form 5, the main inscription according to Form 3 of GOST 21.101 is made.

4.9 The specification of equipment, products and materials is included in the list of reference and attached documents (Form 2 GOST 21.101), in the section “Attached Documents” and is issued to the customer in the quantity established for working drawings.

Form 1

Form 2

________________

* The name of the ministry (department) may not be indicated.

ROSSTANDART FA on technical regulation and metrology
NEW NATIONAL STANDARDS: www.protect.gost.ru
FSUE STANDARDINFORM provision of information from the Russian Products database: www.gostinfo.ru
FA ON TECHNICAL REGULATION"Dangerous goods" system: www.sinatra-gost.ru

DESIGN DOCUMENTATION SYSTEM
FOR CONSTRUCTION

RULES FOR IMPLEMENTING THE SPECIFICATION
EQUIPMENT, PRODUCTS
AND MATERIALS

INTERSTATE SCIENTIFIC AND TECHNICAL COMMISSION FOR STANDARDIZATION AND TECHNICAL REGULATION IN CONSTRUCTION

Moscow

Preface

1 DEVELOPED by the State Enterprise - Center for Methodology, Standardization and Standardization in Construction (GP TsNS), State Design and Construction Institute Project-Montazhavtomatika and State Design, Construction and Research Institute SantekhNIIproekt

INTRODUCED by the Ministry of Construction of Russia

2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization and Technical Regulation in Construction on April 19, 1995

3 ENTERED INTO EFFECT on June 1, 1995 as a state standard of the Russian Federation by Decree of the Ministry of Construction of Russia dated 06/05/95 No. 18-55

4 INSTEAD GOST 21.109-80, GOST 21.110-82 and GOST 21.111-84

3 DEFINITIONS

In this standard the following term is used Specification of equipment, products and materials- a textual design document defining the composition of equipment, products and materials intended for acquisition, preparation and implementation of construction.

4 EXECUTION OF EQUIPMENT SPECIFICATIONS,
PRODUCTS AND MATERIALS

4.1 The specification of equipment, products and materials (hereinafter referred to as the Specification) is drawn up in Form 1 for all main sets of working drawings (except for the main sets of working drawings of building structures).

4.2 The specification includes all equipment, products and materials provided for in the working drawings of the corresponding main set.

4.3 The specification, as a rule, is compiled into sections (subsections), the composition of which, and the sequence of recording equipment, products and materials in them, are established by the relevant SPDS standards.

The name of each section (subsection) is written as a heading in column 2 and underlined.

4.4 The Specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.

4.5 The Specifications indicate:

In column 1 - positional designations of equipment, products provided for in the working drawings of the corresponding main set;

In column 2 - the name of the equipment, product, material, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document;

In column 3 - the type, brand of equipment, product, designation of the standard, technical specifications or other document, as well as the designation of the questionnaire;

In column 4 - code of equipment, product, material according to the product classifier;

About column 5 - name of the equipment manufacturer (for imported equipment - country, company);

Column 6 - designation of the unit of measurement;

In column 7 - the quantity of equipment, products, materials;

In column 8 - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment (weighing up to 25 kg) that does not require the use of lifting vehicles during installation, the column may not be filled in;

Column 9 contains additional information.

4.6 In the Specification, when recording equipment and individually manufactured products, columns 4 and 5 are not filled in, and in column 8 the approximate weight of a piece of equipment is indicated.

4.7 The specification of equipment, products and materials is drawn up as an independent document, which is assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and, separated by a dot, code C.

Example - 2345 - 11 - TX.S, 2345 - 11 - OV.S, 2345 - 11 - ATX.S.

4.8 The first sheet of the Specification is the title page, made according to Form 2.

It is allowed to omit the title page. In this case, on the first sheet of the Specification, instead of the main inscription according to Form 5, the main inscription according to Form 3 GOST 21.101 is made.

4.9 The specification of equipment, products and materials is included in the list of reference and attached documents (Form 2 GOST 21.101), in the section “Attached Documents” and is issued to the customer in the quantity established for working drawings.

* The name of the ministry (department) may not be indicated.

Key words: Specification of equipment, products and materials, execution